Latest Update: 2025/06/11
The below log shows all updates for this product since release:
v1.4 (0.1.4)
- Added MSFS 2024 compatibility (upgraded to a MSFS 2024 native package)
- Added additional model LODs for improved performance (MSFS 2020/2024) and MSFS 2024 compatibility
- Added Just Flight V3 EFB – Features include:
- Added custom Fuel and Payload Menu
- Added support for Navigraph enroute charts.
- Added ability to draw on Navigraph charts
- Added confirmation popup when changing aircraft states
- Improved transition logic between JS/HTML and WASM EFB pages
- Added automatic brightness smoothening to EFB
- Added trim sensitivity saving between flights
- Added linear yoke animation
- Added extra tooltips around the cockpit
- Added paper effect to interactive paper charts
- Fixed position of inboard stall strip on port (left) wing
- Fixed flap sounds playing after flap failure
- Fixed flap 21° position not indicated on MSFS HUD
- Improvements to autopilot behaviour with each GPS selected
- Improvement to GPS brightness logic – each GPS display will now be set to full brightness when the RADIO LIGHTS switch is in the OFF position.
- Improvements to flight model (ground handling)
- Improvements to panel lighting to fix a dark area on the VSI
- Reduced likelihood of aircraft damage occurring due to faults in terrain
- Removed manual from package for compliance with MSFS 2024 SDK (manuals remain available via the PA-38 Tomahawk (MSFS) support page)
- Removed ‘Alternative Clean/Worn Cockpit Textures’ texture sets from package for compliance with MSFS 2024 SDK (alternative cockpit textures now available via the PA-38 Tomahawk (MSFS) support page)
- Updated ‘Optimised Cockpit Textures’ texture sets to support MSFS 2020 and 2024 (available via the PA-38 Tomahawk (MSFS) support page)
- Updated Operations Manual
- Updated EFB Manual
v1.3 (0.1.3) - 2024/07/26
- Limited rudder movement is now possible when stationary but can cause damage if wear is enabled and repeated large inputs are made
- Numerous tweaks to the rate and sensitivity of wear and tear
- OBS 2 option disabled if SL40 is selected (SL40 is COM only)
- Windshield icing is now affected by cabin air, heating and defrost control positions and ambient temperature
- Flap failures caused by wear now prevent movement of the flap surfaces
- Pitot head cover can no longer be fitted in flight
- Opening storm window in flight should no longer cause an overstress warning
- Cockpit lighting optimised to reduce impact on FPS
- Tail navigation light effect fixed
- Landing light bezel fixed
- Minor exterior texture fixes
- Sound fixes and improvements:
- Fixed audio artifacts at 2000RPM
- Improved magneto drop effect
- Added exhaust effects when mixture too lean
- Added walkaround trim tab sounds
- Added gear strut damage sounds
- Other minor improvements and tweaks
- Flight model fixes and improvements, including flap pitch behaviour, oil temperature and pressure and ground handling
v1.2 (0.1.2b) - 2024/04/26
- Fuel tank selector logic fixed.
v1.2 (0.1.2) - 2024/04/26
- Aileron and rudder trim tab adjustment added to walkaround mode, with aileron trim presets for one and two pilot operations.
- ATC not audible - fixed
- Left door latch can no longer be moved with the storm window open
- Fuel pump and selector control assignments fixed
- GTN 750 transponder not responding to inputs – fixed
- Cockpit placard typos fixed
- Digital hour meter sometimes not powering up – fixed
- Battery master switching on when selecting the GNS option on the EFB tablet from cold & dark state – fixed
- Possible to move the rudder when stationary using 'RUDDER AXIS LEFT' and 'RUDDER AXIS RIGHT' control assignments – fixed
- EFB tablet GPS selection fixed
- G-LFSN cockpit registration placard fixed
- Minor sound fixes
- Minor paper chart texture fixes
- Throttle, mixture and magneto/ignition selector not highlighted by MSFS checklist – fixed
- Wear rate option not saving between flights – fixed
The product download in your account is updated as and when updates are released, so if purchasing after any of the given dates your product will include all updates prior to that date.
To download updates you will need to re-download the product from the 'Your Orders' section of your account which you can log into by clicking here.
For guidance on downloading this update, please visit this FAQ.