Latest Update: 16/08/2021


The below log shows all updates for this product since release:


v1.0.6.0

- Fixed startup flag reset after engine spool up (PACKS OFF Lt and CAS message)

- Fixed missing symbols on MFD

- Formula correction for IAS calculation

- Fixed L/R selection in MFD Menus

- Fixed Audio panel volume controls for COM radios

- Several fixes in aircraft.cfg files (airline names, callsigns etc.)

- Flaps indication "1" on EICAS for lever position 1 (physical flaps position = 0)

- Fixed PA/CALL/EMER pushbutton lights

- Camera zoom increased for FCP and Fuel/Defuel Panel cameras

- Camera angle changed for EFB camera

- Fixed setting reserve and taxi fuel on loading a flightplan

- Disabled thrust reserve unlock during cold & dark

- CRJ 550/700 flight model updated

- Fixed Radius to Fix legs

- Fixed a condition where the value for a minute could become 60 and an hour could become 24

- Added math library provided by Asobo to fix airspeed indicator issue

- Fixed shadow center camera

- Added high quality flag for textures (no longer default setting in SU5)


v1.0.3.0 - 30/30/2021

- Changed ETA calculation to base on current UTC time instead of ATD

- Fixed NAV frequencies on MCDU Radio Page showing 0.0 after LOC tuned

- Fixed Coupled VNAV not initiating descent

- Limited range for PFD slip indicator

- Limited range for PFD flight director

- ETA calculation on MFD DATA FPLN Progress page

- ETA calculation on MCDU PERF INIT page 3/3

- Improvements to GPWS mode 3 (altitude loss after takeoff)

- Improvements to GPWS mode 5 (below glideslope)

- Flaps/Slats EICAS animation corrected

- Flaps/Slats exterior model animation corrected

- Added custom glide path calculation

- Adapted GS Hold to custom GS 

- Fixed wrong lbs-kg conversion in EFB ZFW input

- Removed duplicate PA "Remain Seated" after landing

- Added "Low cost carrier" mode for PA and FD announcements (no drinks, no coffee, no sandwiches)

- Increased volume for Gear Up/Down sounds inside the cockpit

- VNAV improvements. Better handling of intermediate level offs

- Fixed EFB ZFW input

- Fixed transparency issue with CRJ-550/700 LOD1 models

- Added functions to allow 180+ degree turns into a given direction

- Added reduced bank angle to MSFS version

- Fixed CF Leg drawing for right turns (Test case: EGHH/26 - EGHH/ILS26/BIA)

- Verified CF Leg drawing for left turns (Test case: EGHI/20 - EGHI/20/EAS)

- Last direct waypoint now disappears from DIR INTC page after the aircraft passed it

- Fixed route zig zagging

- Fixed bearing pointers

- Fixed missing SID-Enroute transitions at end of list

- Fixed wrong heading calculation if both longitudes on a track are equal

- Added support for hardware flaps axis

- Added support for hardware spoiler axis

- Fixed ALT mode switching to ALTS CAP instead of PITCH 

- Added icao_xxx entries to aircraft.cfg

- Updated CRJ-550 model

- Custom Glideslope Hold

- Landing and takeoff behavior improvements in flight model

- Fixed arc and radius to fix drawing routines

- New throttle control mechanics via Simconnect

- Improved ground and flight spoiler effects

- Cruise performance fine tuned to new atmospheric model 

- Take of rotation improved by modified slats/flaps behaviour and new V-Stabilizer calculation

- Improved flight spoiler to meet real world descent rates

- Improved ground spoiler effect for correct lift dumping effect at touch down

- Over all stability in flight improved to feel less wind and turbulence effects

- All flaps stages matching operating handbook reference data and are based on new flaps model

- Correct CoG empty display in modified UI

- UI Load stations with max value reference data

- Fixed (INTC) to Arc leg sequencing (GCFV/01 LORP4Q SID)

- Added arrow in flightplan display for arc legs (RF/AF) with the overfly flag set


v1.0.0.1 - 30/03/2021

- Exterior lights reworked (volumetric effects)

- Nav-to-Nav Transfer should now switch to Nav source VOR/LOC if just one NAV is tuned to an ILS

- Magnetic to true course correction for localizers

- Added function to delete constraints on the LEGS page

- Added IBEX livery

- Custom glide slope hold function

- GLD system now includes spoiler extension on RTO

- Further improvements on throttle control

- Flight model update for spoiler effects

- Fixed IAS/Mach pushbutton not working on the ground

- Increased "green range" for aileron and rudder trim indication on ED2

- Aileron trim now showing properly when between 40 degrees and sim limit

- Fixed missing "A" in HPA in PFD baro indication

- Fixed a CTD when entering a custom waypoint into and empty ALTN FPLN

- Fixed an endless loop (CTD in MSFS) that could occur when calculating a 180 degree DME Arc or Rad Fix leg

- Fixed a double Lbs to KG conversion on the EFB ZFW page

- Improved throttle control (less N1 drops)

- Fixed COM frequency swap

- Fixed selecting COM frequency into scratchpad on FMS radio page

- Fixed flickering RAM AIR OPEN light

- Fixed mouse wheel direction of HOT/COLD switches

- Removed "roll over" effect from the fuel panel mode knob

- Fixed HGS no longer drawing when unpowered

- PA/CHIME/CALL/EMER animations fixed

- Fixed Yoke trim switches

- Fixed ISI glideslope indication only half of that in the PFD

- Fixed COM frequency display on RADIO page

- Added page index and count to RADIO page

- Fixed ZFW data entry limitation

- Added coloured background for active EFB data entry fields

- Added "Parking Brake set" as condition for state changes

- Fixed flight spoiler CAS message

- Fixed "Flightdeck Sounds" EFB setting not saved

- Several fixes to avoid CTDs when selecting arrival without having a departure airport set

- Fixed ZFW direct entries on load sheet

- Limited ZFW direct entry to the range from MZFW and MTOW

- Fixed a bug which could lead to negative passenger weights

- Refuel Panel stops fuelling when parking brake is not set (plus fault light is ON, when attempted)

- Added visual mouse click feedback to EFB

- Reworked colours in EFB

- Several sound volume changes in MSFS

- Fixed APU door opening only 25%

- Fixed yoke stabilizer trim switches

- Added HGS brightness knob animation and clickspots


The product download in your account is updated as and when updates are released, so if purchasing after any of the given dates your product will include all updates prior to that date.


To download updates you will need to re-download the product from the 'Your Orders' section of your account which you can log into by clicking here.

For guidance on downloading this update, please visit this FAQ.