Latest Update: 2024/06/14


The below log shows all updates for this product since release:

v1.1.0 - Sim Update 15

New Features:

- Added support for Control Wheel Steering (CWS) or Vertical Sync autopilot mode.  This allows the operator to hold a button on the yoke to momentarily disconnect the autopilot pitch servos while manually adjusting the aircraft’s pitch.  Releasing the button will have the flight director resume pitch holding at this new pitch.


- CWS can be triggered with either L:var_PilotCws or L:var_CopilotCws.  If you wish to use the native event “K:SYNC_FLIGHT_DIRECTOR_PITCH”, then you must also use the “Control AP Pitch with Hardware Events” tablet option.  “K:SYNC_FLIGHT_DIRECTOR_PITCH” cannot be used when “Control AP Pitch with Hardware Events” is not selected.


- An option has been added to control the autopilot pitch knob with hardware controls.  When “Control AP Pitch with Hardware Events” is selected on the options page of the tablet interface, “AP_PITCH_REF_INC_DN”, “AP_PITCH_REF_INC_UP”, and “AP_PITCH_REF_SET” can be used to adjust the autopilot’s pitch holding reference.  The reference can also now be adjusted with L:var_PilotCws, L:var_CopilotCws or “K:SYNC_FLIGHT_DIRECTOR_PITCH” when using this option.


- In addition to correcting turbocharger critical altitude and improving performance beyond it, the severity of the turbocharger’s overly-rich mixture falloff curve was reduced, thanks to new performance options available in the configuration files.  As a result, you can expect that engine performance will now degrade slowly as you climb beyond the critical altitude with an overly rich mixture. Combustion should not cease, so long as you maintain full throttle while climbing up to the service ceiling; however, a significant reduction of throttle at those altitudes may still result in a total loss of power.


- The tablet can now be dragged around the cockpit while using legacy interaction mode, as opposed to lock mode.


- A persistent tablet option has been added for a static tablet position more comfortable for VR users.  The option, titled “VR Tablet Static Position” will affix the tablet in a location farther away from the camera, obscuring as little instrumentation as possible.


- Added L:Var (L:var_PulseOxyPercent) for accessing the blood oxygen concentration from the tablet’s environmental systems interface.


Bug Fixes:

  • Several aerodynamics and engine performance adjustments were made to improve the accuracy of aircraft cruising speed, fuel burn, and range, particularly at high altitude.  For a complete description of these efforts, see the forum post at https://community.justflight.com/post/29287.  The performance tables have also been reformatted slightly to be easier to read, and more closely resemble the ones from the real aircraft’s flight operations manual.
  • DME holding via the KDI 572R DME did not function due to several contributing factors.
  • Fuel weight totals on the Turbine Duke’s tablet were incorrectly calculated as AVGAS, rather than JET-A, due to an incorrect configuration flag.  Total fuel weight and the resultant estimated range of both aircraft were also less than expected due to an artificially created rounding error.
  • Finally, there is a solution for the simulator’s internal rounding error when setting COM frequencies above ~134 MHz.  These frequencies will now work properly with 3rd party air traffic control clients in all Black Square Aircraft.  The source of this error was discovered to be within the simulator’s core code, but there is a workaround.
  • The right landing light bulb would illuminate with the left landing light instead of the right.
  • Under some circumstances, it was possible for the climate control systems to produce erroneous heating or cooling when flying into air masses of opposite temperature gradient.
  • Newly triggered failures would fail to add themselves to the list of active failures on the tablet when the “Show Only Active Failures” option was selected.
  • The copilot’s side localizer (for use with the KNS-81) could not be rotated through 360°, and could cause the RNAV selected course to exceed 360°.
  • RNAV distance would wind up to 999.9nm when a valid DME station was tuned, but the aircraft was on the ground.  This was due to interpolation added for autopilot control.
  • The surface deicing switch logic was corrected to allow a single L:Var (L:var_SurfaceDeiceSwitch) to control the switch position, and its action.
  • Control surface trim deflections were corrected after confirming that elevator and rudder trim are servo, and aileron trim is anti-servo.
  • A microscopic gap between the pilot’s subpanel and the windshield deicing voltmeter was eliminated.
  • The COM 1 KX155 volume knob animation had a lower maximum position than the COM 2 KXX155.
  • The optional winglet registration number color was not properly set by the configuration in the panel.cfg.
  • Integral illumination removed from the brand label and power knob on the KLN90B.
  • Single pixel mark removed from KLN90B integral lighting emissive texture.
  • The pilot’s HSI and localizer will now display the correct To/From flags when the KLN90B is in OBS mode.  You must also download the latest version of the KLN90B.
  • Decision height annunciator light logic revised for persistent illumination below the decision height until below 20ft radar altitude.
  • It was impossible to disable external power via the tablet switch on the ground when either the chocks or parking brake were deployed.
  • The placard on the copilot’s side wall previously displayed two redundant recommended approach speeds in both the Piston and Turbine Duke, while it was meant to display two different recommended approach speeds for the two aircraft, and one maximum recommended crosswind component.
  • Corrected surface deicing description in the manual which retained language from the TBM 850 not applicable to the Dukes.
  • Corrections to various input and output variables and events in the manual’s “Hardware Inputs & Outputs” section, including L:var_RNAV_CHECKMODE, and L:var_FlightDirectorVisible.


v0.1.0 - 2024/05/09

- Initial Release Version

The product download in your account is updated as and when updates are released, so if purchasing after any of the given dates your product will include all updates prior to that date.


To download updates you will need to re-download the product from the 'Your Orders' section of your account which you can log into by clicking here.

For guidance on downloading this update, please visit this FAQ.